problem: stuck rudder trim
-
- Posts: 7
- Joined: Wed Aug 29, 2018 2:40 pm
- Location: AL
- Contact:
problem: stuck rudder trim
Hey all,
I'm new to Maules ... recently acquired an M7-235.
After a recent flight, I discovered my rudder trim tab was stuck in position, full deflection off to one side. I'd never even touched the rudder trim adjustment T-handle, so I'm baffled.
On the ground, once discovering it, I tried unlocking and adjusting the T-handle in various ways, tried wiggling the rudder, and tried a bit of pressure by hand on the trim tab. And I can't figure out how to get it unstuck. I hope it's something obvious, but I'm missing it.
Anyone have any ideas what might have happened? And how I go about solving this?
Thanks.
I'm new to Maules ... recently acquired an M7-235.
After a recent flight, I discovered my rudder trim tab was stuck in position, full deflection off to one side. I'd never even touched the rudder trim adjustment T-handle, so I'm baffled.
On the ground, once discovering it, I tried unlocking and adjusting the T-handle in various ways, tried wiggling the rudder, and tried a bit of pressure by hand on the trim tab. And I can't figure out how to get it unstuck. I hope it's something obvious, but I'm missing it.
Anyone have any ideas what might have happened? And how I go about solving this?
Thanks.
-
- Posts: 7
- Joined: Wed Aug 29, 2018 2:40 pm
- Location: AL
- Contact:
-
- 100+ Posts
- Posts: 422
- Joined: Sun Feb 03, 2013 7:10 pm
- Contact:
Move the aeloin by hand watch the rudder tab move. ( after you put it back together) It's a servo tab to reduce the effects of adverse yaw and assist keeping coordinated.
The twist lock handle under the Rt. side yoke is spring loaded applying pressure to the Rt. rudder pedal . Pulling it out on takeoff and you don't have to push right rudder nearly as hard.
The twist lock handle under the Rt. side yoke is spring loaded applying pressure to the Rt. rudder pedal . Pulling it out on takeoff and you don't have to push right rudder nearly as hard.
The best Government, is less Government.
-
- Posts: 41
- Joined: Mon Aug 21, 2017 2:25 pm
- Location: Tennessee
- Contact:
rudder trim tab, "servo tab"
There is a previous post that might be helpful. The rudder trim tab, what some are calling the "servo tab" is connected to the aileron cable via its own cables on the left and right side. When you use the yoke to bank left or right the aileron cable not only actuates the aileron, it also actuates the rudder trim tab ("servo tab"). When the cables are adjusted properly the aileron cable pulls on the rudder trim tab cable to help coordinate the turn. The rudder trim tab cable is attached to the aileron cable just within the headliner over the pilot and co-pilots seat. Unzip the headliner and you will see the cables and their attachments. Yours may simply need adjustment.
Mine broke and needed a new cable. Good luck, Ron Hallmark
Mine broke and needed a new cable. Good luck, Ron Hallmark
-
- 100+ Posts
- Posts: 737
- Joined: Tue Oct 17, 2006 3:07 pm
- Location: KGCY
- Contact:
The tab is interconnected to the ailerons as described above. When you get back to the airplane move the ailerons and you should see the tab move.
Not sure that Ron is correct on the rudder trim. (T handle). My understanding is that it applies spring tension to the rudder cable not at the aileron interconnect above.
Either way, the T handle, which is trim, does not move the servo tab that is interconnected to the ailerons.
Kirk
Not sure that Ron is correct on the rudder trim. (T handle). My understanding is that it applies spring tension to the rudder cable not at the aileron interconnect above.
Either way, the T handle, which is trim, does not move the servo tab that is interconnected to the ailerons.
Kirk
-
- Posts: 41
- Joined: Mon Aug 21, 2017 2:25 pm
- Location: Tennessee
- Contact:
I did not mention the rudder trim (T handle). I don't really know exactly how that works yet. I had enough trouble digging out the info on the rudder trim tab, and the cables that connect the rudder trim tab to the aileron cables. I think it might have been a previous poster who mentioned the T-Handle.
Ron
Ron
-
- Posts: 41
- Joined: Mon Aug 21, 2017 2:25 pm
- Location: Tennessee
- Contact:
- Andy Young
- 100+ Posts
- Posts: 1548
- Joined: Wed Oct 05, 2011 7:10 am
- Location: Alaska, Antarctica, Colorado, and Others
- Contact:
It seems like it might be helpful at this point to define terms, to avoid confusion.
The tab on the back of the rudder is called a SERVO tab; it is NOT a trim tab. Many airplanes have trim tabs in the same location, but Maules do not. It is not directly pilot-controllable, nor is it ground-adjustable; it responds to aileron deflection via small cables, as previously mentioned.
Rudder TRIM is accomplished via the T handle on the panel, which pulls on a cable that pulls on the right rudder pedal on the co-pilot side.
The tab on the back of the rudder is called a SERVO tab; it is NOT a trim tab. Many airplanes have trim tabs in the same location, but Maules do not. It is not directly pilot-controllable, nor is it ground-adjustable; it responds to aileron deflection via small cables, as previously mentioned.
Rudder TRIM is accomplished via the T handle on the panel, which pulls on a cable that pulls on the right rudder pedal on the co-pilot side.
Last edited by Andy Young on Tue Jun 11, 2019 8:12 am, edited 1 time in total.
- rv8bldr
- Posts: 45
- Joined: Thu Feb 08, 2018 9:28 am
- Location: Pakenham, Ontario, Canada
- Contact:
Um.... that's confusing The tab on the RUDDER is a servo tab, not the ELEVATOR.Andy Young wrote:It seems like it might be helpful at this point to define terms, to avoid confusion.
The tab on the back of the elevator is called a SERVO tab; it is NOT a trim tab. Many airplanes have trim tabs in the same location, but Maules do not. It is not directly pilot-controllable, nor is it ground-adjustable; it responds to aileron deflection via small cables, as previously mentioned.
Rudder TRIM is accomplished via the T handle on the panel, which pulls on a cable that pulls on the right rudder pedal on the co-pilot side.
Cheers
Mark
President EAA Chapter 245
'79 Maule M5-235C C-GJFK
RV-8 C-GURV (Sold)
Bearhawk 4pl C-GPFG - Under Construction
President EAA Chapter 245
'79 Maule M5-235C C-GJFK
RV-8 C-GURV (Sold)
Bearhawk 4pl C-GPFG - Under Construction
- Andy Young
- 100+ Posts
- Posts: 1548
- Joined: Wed Oct 05, 2011 7:10 am
- Location: Alaska, Antarctica, Colorado, and Others
- Contact:
-
- Posts: 41
- Joined: Mon Aug 21, 2017 2:25 pm
- Location: Tennessee
- Contact:
Okay I am still trying to learn...................so, I had to get the M-5 Parts Catalog CD, and study it to get an idea about how to install/replace a broken cable. The CD is for the M-5 so it might not apply to the M-7. When you look at the control group section of the CD it shows drawings of the individual parts and where they are located. Drawing #3173B is labeled "Rudder Tab Assembly," Drawing #3171B is labeled "Rudder Tab," other related drawings, #3018A "Rudder Tab Cable Clamp Assembly," #3019B "Rudder Tab Cable Fairlead Assembly," #3020B "Rudder Tab Pulley Assembly." I could not find any reference to "Servo Tab" on any of the drawings in the CD. Also, there seems to be a discrepancy in the quotations of the posts. When I read Andy's post it does say "The Tab on the back of the RUDDER is called a Servo Tab", but when RV8BLDR quotes Andy his quote says "The tab on the back of the ELEVATOR is called a SERVO tab." .........?????? Sorry about all of the confusion.
Ron Hallmark
Ron Hallmark
- Duane
- 100+ Posts
- Posts: 762
- Joined: Mon Apr 07, 2008 1:58 pm
- Location: moultrie ga
- Contact:
- rv8bldr
- Posts: 45
- Joined: Thu Feb 08, 2018 9:28 am
- Location: Pakenham, Ontario, Canada
- Contact:
Hey RonRon Hallmark wrote: Stuff deleted...
When I read Andy's post it does say "The Tab on the back of the RUDDER is called a Servo Tab", but when RV8BLDR quotes Andy his quote says "The tab on the back of the ELEVATOR is called a SERVO tab." .........?????? Sorry about all of the confusion.
Ron Hallmark
That's because Andy went back and corrected his original post after I pointed out the error. You can ignore my post (and me, if you like ),
Cheers
Mark
President EAA Chapter 245
'79 Maule M5-235C C-GJFK
RV-8 C-GURV (Sold)
Bearhawk 4pl C-GPFG - Under Construction
President EAA Chapter 245
'79 Maule M5-235C C-GJFK
RV-8 C-GURV (Sold)
Bearhawk 4pl C-GPFG - Under Construction
- Andy Young
- 100+ Posts
- Posts: 1548
- Joined: Wed Oct 05, 2011 7:10 am
- Location: Alaska, Antarctica, Colorado, and Others
- Contact:
I haven’t looked at the parts CD, but it sounds like Maule might not use the word “servoâ€, just using the more generic “tabâ€.
Here’s the distinction, as I understand it:
A servo tab is one that responds to the movement of one control surface to influence the movement of another control surface. In the case of our Maules, when the aileron is moved, it pulls on a small cable that deflects the tab on the back of the rudder, which then wants to push the rudder to one side.
A trim tab is one that is either controlled from the cockpit to deflect the control surface (like the one on our left elevators) or is a fixed piece that is set on the ground by bending (some Maules have had this installed on their ailerons, but the Maule factory never did this to my knowledge).
What can be confusing is that many airplanes have cockpit-controllable trim tabs mounted on the back of the rudder that look just like our rudder tabs that are NOT controlled from the cockpit, but are instead slaved to the ailerons.
This is why I find it useful to distinguish our rudder tab as a “servo†in an effort to clarify what it is doing vs. trim tabs that most people are more used to seeing.
Here’s the distinction, as I understand it:
A servo tab is one that responds to the movement of one control surface to influence the movement of another control surface. In the case of our Maules, when the aileron is moved, it pulls on a small cable that deflects the tab on the back of the rudder, which then wants to push the rudder to one side.
A trim tab is one that is either controlled from the cockpit to deflect the control surface (like the one on our left elevators) or is a fixed piece that is set on the ground by bending (some Maules have had this installed on their ailerons, but the Maule factory never did this to my knowledge).
What can be confusing is that many airplanes have cockpit-controllable trim tabs mounted on the back of the rudder that look just like our rudder tabs that are NOT controlled from the cockpit, but are instead slaved to the ailerons.
This is why I find it useful to distinguish our rudder tab as a “servo†in an effort to clarify what it is doing vs. trim tabs that most people are more used to seeing.
-
- Posts: 41
- Joined: Mon Aug 21, 2017 2:25 pm
- Location: Tennessee
- Contact:
Andy that sums it up very well. Mark, I didn't know Andy had corrected his error. I am thankful that we can put this post to bed...........Now I have another little problem that I'd like you guys to chew on a little. My alternator may be going bad, and I don't know how to know for sure. When there is minimum draw on the electrical system my ammeter is showing a slight positive charge, but when I turn on my landing lights the indicator goes into the negative. So, as long as I am flying along with strobes, nav lights, transponder and radio on the ammeter indicates + but when I turn on the landing lights it goes to - (negative) These are the old style halogen landing lights and there are two of them. Should I think about rebuilding the alternator????
Ron
Ron
Who is online
Users browsing this forum: No registered users and 11 guests