Is there any potential problem with flying at speeds of 90mph for a trip lasting 2 hours each way? The engine is a Lycoming O-360-C1F. Looking through the engine operator's manual, I can see values for Economy Cruise at 65%, but that's still around 110mph in this plane. Yesterday I tested running at 50% for a short period, with the engine monitor looking like this:
https://merrymunks.com/20190720_154627/
(Side note, the CHT on #4 shows lower due to sensor placement; manual temp measurement shows that cylinder has a similar heat profile to the others.)
50% resulted in a 105mph airspeed. Are there any potential hazards to reducing further to get 90mph? I can get to 90 in the pattern with full prop and manifold back to about 10-12, but have never tested running that way over an extended period of time.
Engine questions, extended slow flight, M5-180-C
- merrymunks
- Posts: 32
- Joined: Fri Apr 20, 2018 2:53 pm
- Location: KSPB
- Contact:
- montana maule
- 100+ Posts
- Posts: 310
- Joined: Sun Sep 24, 2006 7:27 am
- Contact:
It's been my experience with the small Lycoming engines to get them to stated TBO they need to be run at 65 -70% power. You can run them at lower power settings but you won't get the life out of them. Lycoming says oil temps need to be at 180F for over an hour at a time to get the best life from the engine.
Also from what I have noticed if I lean to peak EGT I get the same MPG if I run at 65% or at 50% power. I just get get there quicker at 65%.
Also from what I have noticed if I lean to peak EGT I get the same MPG if I run at 65% or at 50% power. I just get get there quicker at 65%.
- Mog
- 100+ Posts
- Posts: 990
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
- merrymunks
- Posts: 32
- Joined: Fri Apr 20, 2018 2:53 pm
- Location: KSPB
- Contact:
- Mog
- 100+ Posts
- Posts: 990
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
I run a franklin which really likes high RPM. With a virtually stock M4 I found it very frustrating to operate in the 80-90mph cruise range. I would run this for up to an hour or more and i was constantly dropping in flaps for drag or making s-turns to keep in pace. Now, with big tires and a few other really draggy items I can certainly get down in speed a bit easier. But I don’t like pacing sub 90mph planes for very long.
- merrymunks
- Posts: 32
- Joined: Fri Apr 20, 2018 2:53 pm
- Location: KSPB
- Contact:
Thanks Montana, really good information about power & engine temps. Didn't know about running over an hour @ at 180* with regards to TBO. I think I might be practicing landings too much, need to do more x-country...montana maule wrote:It's been my experience with the small Lycoming engines to get them to stated TBO they need to be run at 65 -70% power. You can run them at lower power settings but you won't get the life out of them. Lycoming says oil temps need to be at 180F for over an hour at a time to get the best life from the engine.
Also from what I have noticed if I lean to peak EGT I get the same MPG if I run at 65% or at 50% power. I just get get there quicker at 65%.
M5-180-C
- montana maule
- 100+ Posts
- Posts: 310
- Joined: Sun Sep 24, 2006 7:27 am
- Contact:
-
- 100+ Posts
- Posts: 422
- Joined: Sun Feb 03, 2013 7:10 pm
- Contact:
Who is online
Users browsing this forum: No registered users and 4 guests