Is elevator trim tab with piano hinge more effective?
-
- 100+ Posts
- Posts: 435
- Joined: Wed Sep 12, 2012 12:25 pm
- Contact:
Is elevator trim tab with piano hinge more effective?
Have the old style m4/m5 trim tab. It won't trim out for approach. Will the piano hinge type of elevator tab like on a m7 provide more trim? [/i]
- Mog
- 100+ Posts
- Posts: 980
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
-
- 100+ Posts
- Posts: 735
- Joined: Tue Oct 17, 2006 3:07 pm
- Location: KGCY
- Contact:
-
- Posts: 95
- Joined: Sun Oct 15, 2006 7:57 am
- Location: Circle Montana
- Contact:
-
- Posts: 85
- Joined: Mon Feb 18, 2019 8:29 am
- Location: NorCal
- Contact:
I am in the process of changing over to the new style hinge on my M5. I will try to give some feed back on that once I get done.
My M5 235 you can trim it hands off on approach with one person and half fuel, and that is well to the front of the CG curve.
I don't use the trim past about half way back though. Your right arm will become used to the pressures it takes to be at the attitude you want. I have found that it helps me fly a more stabilized approach with just your arm. The other advantage is that you dont have to force the nose down for a wheel landing, and the plane does not want to point straight to the sky for a go-around.
My M5 235 you can trim it hands off on approach with one person and half fuel, and that is well to the front of the CG curve.
I don't use the trim past about half way back though. Your right arm will become used to the pressures it takes to be at the attitude you want. I have found that it helps me fly a more stabilized approach with just your arm. The other advantage is that you dont have to force the nose down for a wheel landing, and the plane does not want to point straight to the sky for a go-around.
No great story started with a good idea...
-
- Posts: 85
- Joined: Mon Feb 18, 2019 8:29 am
- Location: NorCal
- Contact:
-
- 100+ Posts
- Posts: 435
- Joined: Wed Sep 12, 2012 12:25 pm
- Contact:
Good point on the tension I'll go check that this morning. It's a 235 but even so I'd hope I could trim it to approach at least 65 on its own. Going to play with it ill get back with results.
Also Yesterday was noticing slop in my flaps where I wasn't getting full deflection under load. Culprit was that gust lock. Needs to go byebye.
Does anyone put half a degree wash out into the wings or do you run them flat. I get a oil canning bad when adding wash.
Also Yesterday was noticing slop in my flaps where I wasn't getting full deflection under load. Culprit was that gust lock. Needs to go byebye.
Does anyone put half a degree wash out into the wings or do you run them flat. I get a oil canning bad when adding wash.
-
- 100+ Posts
- Posts: 735
- Joined: Tue Oct 17, 2006 3:07 pm
- Location: KGCY
- Contact:
-
- 100+ Posts
- Posts: 435
- Joined: Wed Sep 12, 2012 12:25 pm
- Contact:
So I did have a little slop in my trim cable. Also tightened up the flap turnbuckle so now my flaps actually stay down 40 degrees during landing instead of 15, however now their hanging down 4 inches unless the air is holding them up in flight. Gust locks fault I presume. Springs are good.
Time to find some piano hinge and get started on the m7 trim tab.
Approach speed full up trim full flap is 65 without elevator input, no flap approach trims out at 95mph. Still lacks some trim but much better with more flap. Not so sure what u mean by gap seals on the trim tab. Maybe u meant the elevator. Already have those.
Looking at the gust lock I need to build a bracket to hold the return spring. Should be easy.
My only gripe now is the rudder is too small and tail too big. Got a cross wind gust hanging her off the prop and about went in the trees. Then went to take back off and about stuck it in the trees again when the p factor hit and the rudder ran out. No short takeoffs in this pig. Hoping the long cord m7 rudder helps. I prefer the m4 tail far more, crosswinds are a non issue and it's far more responsive.
Back to work
Time to find some piano hinge and get started on the m7 trim tab.
Approach speed full up trim full flap is 65 without elevator input, no flap approach trims out at 95mph. Still lacks some trim but much better with more flap. Not so sure what u mean by gap seals on the trim tab. Maybe u meant the elevator. Already have those.
Looking at the gust lock I need to build a bracket to hold the return spring. Should be easy.
My only gripe now is the rudder is too small and tail too big. Got a cross wind gust hanging her off the prop and about went in the trees. Then went to take back off and about stuck it in the trees again when the p factor hit and the rudder ran out. No short takeoffs in this pig. Hoping the long cord m7 rudder helps. I prefer the m4 tail far more, crosswinds are a non issue and it's far more responsive.
Back to work
- Mog
- 100+ Posts
- Posts: 980
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
Who is online
Users browsing this forum: No registered users and 11 guests