Split Rear (sling) Seat
-
- 100+ Posts
- Posts: 298
- Joined: Sat Dec 22, 2018 1:09 pm
- Location: KY+AK
- Contact:
Split Rear (sling) Seat
Hello all,
When rebuilding my M7 I'm hoping to split the rear sling seat into two pieces so I could run the airplane in a configuration with 3 people and room for bulky/long cargo. Seems easy enough - just cut the rear seat upholstery in half and add some material to close off the cut sides. My airframe has the mount points for individual seat belts back there so that is no issue. I realize the mount bars would still be in place and limit some cargo but it would still create more space.
Clearly it can be done easily but wondering if anyone had went this route and had any pictures, lessons learned, ideas, etc so I don't re-invent the wheel.
Thanks,
Asa
When rebuilding my M7 I'm hoping to split the rear sling seat into two pieces so I could run the airplane in a configuration with 3 people and room for bulky/long cargo. Seems easy enough - just cut the rear seat upholstery in half and add some material to close off the cut sides. My airframe has the mount points for individual seat belts back there so that is no issue. I realize the mount bars would still be in place and limit some cargo but it would still create more space.
Clearly it can be done easily but wondering if anyone had went this route and had any pictures, lessons learned, ideas, etc so I don't re-invent the wheel.
Thanks,
Asa
- montana maule
- 100+ Posts
- Posts: 309
- Joined: Sun Sep 24, 2006 7:27 am
- Contact:
Re: Split Rear (sling) Seat
I did exactly that so I could set more gear on the floor next to the back seat passenger. I found someone to sell me an extra set of back seat cushions and the sling. Took it to an upholstery shop and had them cut it in half and patch the open end. It's not the same color or material as my interior but it works. If not needed I put my original seats back in. I tried to talk the factory into making me the set but I didn't get very far with the idea. I'll try to get some pictures.
-
- 100+ Posts
- Posts: 298
- Joined: Sat Dec 22, 2018 1:09 pm
- Location: KY+AK
- Contact:
Re: Split Rear (sling) Seat
Thanks! Yes, would love pictures. I was going to do it with my original seat so it would still match. Not ready to give up my strip club red interior.montana maule wrote: ↑Mon Jul 26, 2021 4:59 pmI did exactly that so I could set more gear on the floor next to the back seat passenger. I found someone to sell me an extra set of back seat cushions and the sling. Took it to an upholstery shop and had them cut it in half and patch the open end. It's not the same color or material as my interior but it works. If not needed I put my original seats back in. I tried to talk the factory into making me the set but I didn't get very far with the idea. I'll try to get some pictures.
- Andy Young
- 100+ Posts
- Posts: 1548
- Joined: Wed Oct 05, 2011 7:10 am
- Location: Alaska, Antarctica, Colorado, and Others
- Contact:
Re: Split Rear (sling) Seat
I think that’s more “Brothel Red”, Asa.
- montana maule
- 100+ Posts
- Posts: 309
- Joined: Sun Sep 24, 2006 7:27 am
- Contact:
-
- 100+ Posts
- Posts: 298
- Joined: Sat Dec 22, 2018 1:09 pm
- Location: KY+AK
- Contact:
Re: Split Rear (sling) Seat
A little confused as to why you'd need to cut/weld anything but end product is exactly what I'm looking for. Thanks!
- andy
- Site Admin
- Posts: 1667
- Joined: Mon Aug 06, 2007 2:05 pm
- Location: Lake James, NC, USA
- Contact:
Re: Split Rear (sling) Seat
I think there's a metal frame inside the sling seat bottom to keep its shape. There are some curved pieces of metal on the seat bottom that fit over the bottom seat tube to keep it from moving forward and allow it to pivot up from the back edge. Shortening the seat bottom and moving one of the curved metal pieces would require re-welding.
Andy
1986 MX7-180
1986 MX7-180
- montana maule
- 100+ Posts
- Posts: 309
- Joined: Sun Sep 24, 2006 7:27 am
- Contact:
-
- 100+ Posts
- Posts: 298
- Joined: Sat Dec 22, 2018 1:09 pm
- Location: KY+AK
- Contact:
Re: Split Rear (sling) Seat
Ahhhh, got it. Thanks!
- Jayson v Schalkwyk
- 100+ Posts
- Posts: 123
- Joined: Mon Sep 14, 2015 1:05 pm
- Location: Himeville, South Africa
- Contact:
Re: Split Rear (sling) Seat
in May, Maule made an announcement on their Facebook page that they have now got FAA approval for the split style rear sling seat. Might be something for folks to look into - contact Maule parts for more info.
1983 M6-235C
Who is online
Users browsing this forum: No registered users and 13 guests