Replacing Dzus Fasteners in Cowling
- crhannay
- Posts: 51
- Joined: Thu Aug 30, 2018 7:36 am
- Location: Afton, Wyoming
- Contact:
Replacing Dzus Fasteners in Cowling
I want to replace my old Dzus fasteners on my cowlings with stainless steel ones prior to painting. Has anyone done this? I would appreciate any and all advice on how to do this without damaging the fiberglass surrounding the grommet.
Help Curt
Help Curt
Last edited by crhannay on Sat May 18, 2019 5:08 am, edited 2 times in total.
- FARMAULE
- 100+ Posts
- Posts: 194
- Joined: Wed Oct 24, 2012 1:31 pm
- Location: West Virginia
- Contact:
I just replaced all of mine with camlocs. Start from behind and meticulously crush all of the retainers (the swollen portion of the dzus) holding the fasteners too the cowl. This enabled me to have more room under the head of the fastener and more play all around. Now take a thin piece of solid metal (thin enough to place between the fiberglass and head of the dzus) and firmly push towards the fiberglass and with on swift hit of a wooden mallet from behind they literally just pop out. There is a good video on YouTube that explains my method just slightly different. Also I am way happier with the camlocs. Something to think about. Goodluck
- crhannay
- Posts: 51
- Joined: Thu Aug 30, 2018 7:36 am
- Location: Afton, Wyoming
- Contact:
- FARMAULE
- 100+ Posts
- Posts: 194
- Joined: Wed Oct 24, 2012 1:31 pm
- Location: West Virginia
- Contact:
The hole diameter went up for the camloc and the rivet mounting holes were the exact same spacing to just rivet on the camloc receptacles on the female side. I didn’t have to do glass work for the camlocs to work but I did redo my cowl due to some cracks and separation. I guess the variables in camloc and dzus fasteners could change the outcome for individual aircraft and maybe I got lucky.
- crhannay
- Posts: 51
- Joined: Thu Aug 30, 2018 7:36 am
- Location: Afton, Wyoming
- Contact:
- Mog
- 100+ Posts
- Posts: 980
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
- crhannay
- Posts: 51
- Joined: Thu Aug 30, 2018 7:36 am
- Location: Afton, Wyoming
- Contact:
- Mog
- 100+ Posts
- Posts: 980
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
- crhannay
- Posts: 51
- Joined: Thu Aug 30, 2018 7:36 am
- Location: Afton, Wyoming
- Contact:
My worry is that the grommet would come out with the stud and mess up the 3/8" hole in the fiberglass. I thought about the cutting the stud or at least grinding it down a bit with a diamond bit so it would slide out easier. I like the counter sink idea. I was thinking of using 3/8" of slightly smaller drill bit through the grommet.
- crhannay
- Posts: 51
- Joined: Thu Aug 30, 2018 7:36 am
- Location: Afton, Wyoming
- Contact:
Did you use fixed or floating receptacles, and also can you tell me what length studs you used and in what locations? The sides of the lower cowling should be the shortest, the sides of the top cowling where it mates to the lower cowl should be a medium length, and the ones across the top rear of the of the top cowling are the longest. I talked to Maule and they said most of them are 40S5-6S studs, but is kind of trial and error to get the best fit.
- Mog
- 100+ Posts
- Posts: 980
- Joined: Fri Nov 26, 2010 8:01 pm
- Location: Dallas, TX
- Contact:
Who is online
Users browsing this forum: No registered users and 15 guests